1.It is best to allow the rotor to rotate freely.

1.最好自由旋。

2.One solution is to add a rotor position sensor to the synchromotor.

2.解决这一问题普遍的做法是加装电机位置传感器。

3.Therefore, the stator and rotor and the vent was spinor into two parts.

3.因此，定的不退、排气口被和旋隔成两个局部。

4.The stability of turbocompressor rotor bearing system is a very important problem.

4.透平压缩机轴承系统的稳定性是一个非常重要的问题。

5.As the core component,rotor system may run abnormally,have the failures of unbalance,bearing damage and incorret alignment.

5.作为它的核心部件，系统运行过程中可能出现不平衡、不对中、轴承损坏等故障。

6.Large totating machinery is one of the key equipments in national foundation establishment and industry.

6.大型旋机械是国家基础设施和基础工业中关键的设备之一，旋机械向着速、效发展，对旋机械的动力特性、可靠性也提出了更的要求，这些现实需要促进了动力学的发展。

7.Stepped and staggered sidecutter is the special miller for machining root rotor slot by Beijing Beizhong Steam Turbine Generator Co.

7.台阶错齿三面刃铣刀是北京北重汽轮有限责任公司加工叶根槽的专用铣刀。

8.We manufacture more than 100 types turbocharge rotor assembly and many series, H, HX, TA, TB, GT, and so on.

8.生产的总成，有H、HX、TA、TB、GT、小松、江雁、石川岛等系的产品，100多种型号。

9.MAZDA RX 7 Car is equipped with Wankel double cylinder rotary engine with turbosupercharger, which adopts ECU control ignition and fuel injection systems.

9.马自达RX-7型轿车采用带蜗轮增压器的汪克尔式双缸发动机。

10.Our company is specialized in producing RBB series of flexible rotor series of pumps, the pump is a self-suction pump of good volume.

10.我公司是专业生产RBB系柔性糸，该是一种自吸性能良好的容积。

11.Fireresistant Hall device and SmCo rotor is used to design position and speed sensor, and the corresponding doubling circuit and decoding circuit is designed.

11.采用耐温的锁定型霍尔元件和钐钴永磁分别构成位置与速度传感器，并设计相应的速度信号倍频电路与位置信号译码电路。

12.The new type of rotary compressor has two key parts, an outer rotor and an inner one which employs isometric curve of trochoid as its profile.

12.从理论上分析了一种新型内、外结构回式压缩机,其内型线由短幅外摆线的内等距线构成。

13.Based on this, the veracity of the rotor fault diagnosis can be improved through the distance of the information entropy curve chart at the multispeed.

13.实例计算表明，信息熵距能够较好的区分故障类别，在此基础上，通过多速下的熵距曲线图可以提故障诊断的准确性。

14.The rotor is then heated and pressfit onto a cooled precision-machined one-piece stainless steel shaft and the assembly is then machined and balanced as a unit.

14.经过加热后压入配合进经过冷精密加工的一体式不锈钢轴内，然后机械和平衡设备装配成一个整体。

15.The dynamic equation of the transient response in a cracked rotor system was modelled, the numerical simulation solutions of the uncracked rotor and the cracked rotor were obtained.

15.摘要基于建立的裂纹瞬态回应动力学模型，得到了有无裂纹的数值仿真解。

16.Fitting is used for autobicycle start electrical machiney, Car forced convection air heater, Electric tool electrical machiney waits for miniature electrical machiney rotor slot insert empire paper.

16.适用于摩托车起动电机、汽车暖风机、电动工具电机等微型电机槽插入绝缘纸。

17.According to the formation principle of the tritubercular cycloid in this paper, the rotor, whose bore curve is the inner envelope line of the cycloid, is made with the solid radius vector.

17.根据三尖摆线的形成原理,以摆线的内包络线为定内腔曲线,动径实体化后作为,定、按照一定关系运动则形成一种新型摆线。