1.Soot is the product of the imperfect combustion of fuel.

1.煤烟是燃料不完燃烧的产物。

2.These results are instructively important for determining combustion heat safely.

2.这些结果地测定燃烧热具有指导意义。

3.Soot is usually the product of the imperfect combustion of fuel.

3.煤烟通常是燃料不完燃烧的产物。

4.Usually a gas cooler is used between the combustion chamber and hydrator.

4.通常在燃烧室和水合器之间设置一个气体冷却器。

5.A model of pyrotechnical combustion products was established based on the principle of minimum free-energy.

5.燃烧产物的预测烟火药的设计非常重要。

6.The paper discusses the calculation and its property of the rate of combustion heatrelease for prechamber diesel engines.

6.文章讨论了予燃室柴油机的燃烧热规律的计算特点和方法。

7.Reference on step conversion of coal gasification and carbocoal combustion is offered by the research on pyrolysis carbocoal.

7.热解半焦的研为煤气及半焦燃烧的分级转技术提供了参考。

8.Sugariness is in digestive process, if the word because of without complete combustion corruption, will become lactic acid.

8.糖质在消的过程，如果因为没有完燃烧而腐败的话，将会变成乳酸。

9.All the results can be used to validate the autoignition and combustion models of homogeneous mixture in vitiated coflow.

9.为活热氛围下液体燃料自燃及燃烧模型的建立奠定了基础。

10.The technigue of staged coal combustion in underplate burning boiler is a mew method for energy saving and environment protecting.

10.层燃炉两段燃烧技术,是一种行之有效的节能、环保的新技术。

11.Besides, laser optoacoustic spectroscopy technique and laser mass spectrometry will play more important role in research of internal combustion engine.

11.另外，激光光声光谱技术、激光质谱仪等有望在内燃机的研挥更大的作用。

12.The influence of afterburning chamber length on secondary combustion efficiency and flow field were analyzed based on direct-connected ground simulation test.

12.结合直连式地面模拟试验,分析了补燃室长度掺混流场和二次燃烧效率的影响。

13.Preliminary test of combusting property of COWS showed that this kind of synfuel had a good combustion behavior, and high combustion efficiency.

13.燃烧性实验表明，三元料浆的燃烧性能良好，燃烧效率高，是一种工业应用前景广阔的浆体。

14.The heat input of gasification using coalite as solid heat carrier comes from combustion heat of the solid heat carrier in riser.

14.固体热载体煤气的热量靠提升燃烧产生。

15.Three technology options including precombusfion capture,oxyen-fired combustion and postcombustion capture and their process flows for capturing CO2 are introduced in this paper.

15.文章主要介绍了3种CO2捕获技术:燃烧前捕获、纯氧燃烧、燃烧后捕获,并介绍了其工艺流程。

16.Multiphase flow is a new and developing discipline on the basis of hydrodynamics, heat and mass transfer, physiochemistry, combustion theory and other disciplines.

16.多相流是在流体力学传热传质学,生物学,燃烧学等多学科的基础上展起来的一门新兴学科.

17.Based on polytrophic process of air compression and isothermal gas combustion inside the turbine, an improved gas turbine with generality Carnot cycle is suggested.

17.基于气体多变压缩以及等温涡轮燃烧技术,提出了一种改进的概括性卡诺循环燃气轮机,通过模型预测分析了其性能,并与传统燃气轮机进行了比较。

18.The tribophysics of the cylinder liner—piston rings in an internal combustion engine is a typical tribological system with the reciprocating motion and the impacting motion.

18.内燃机缸套——活塞环摩擦副系统是一个集往复、冲击于一体的典型的摩擦学系统。

19.Both numerical prediction and experiments signified that the new type flameholder has a bright prospect as a kind of high combustion efficiency and low pressure loss flameholder.

19.无论计算还是实验，都表明新型稳定器作为高效 低阻火焰稳定器是很有展前景的。

20.This paper discusses the fundamentals and characteristics of catalytic combustion and the type of catalyst and approaches the way to apply the technology of catalytic combustion in cremator.

20.本文催燃烧法的基本原理、特点及催剂的形式等方面进行了讨论,并就催燃烧技术在火设备实现的可能方法进行了探讨。