1.There aren't any slots available until next month.

1.在下个月之前都没有空位。

2.Can you slot her into a job in the sales department?

2.你能把她安排在销售部作吗?

3.Put a coin in the slot.

3.将硬币放入投币口。

4.When we got the final result of our experiment, everything slotted into place.

4.我们得到了试验的最终结果，一切都吻合。

5.If you put a coin in the slot of this machine, stamps come out of another slot.

5.如果你把硬币放进这台机器的一个投币口，邮票就会从另一个口里出来。

6.The programme of "front benching pilot tunnel divisional and laminated skewed slot construction" was created.

6.独创了“正台阶导硐分部分层斜方案”,该方案具有良好的推广应价值。

7.There are a number of thoughtful slots and pockets for storing things, including a lighted glovebox.

7.，乐骋有若干深思的储存物品空间，包括一个浅的手套箱。

8.It is an important problem to indicate the maximum displacement coefficient ingear slotting tool design process.

8.确定最大变位系数是插齿刀设计的一个重要问题。

9.Please comment whether it's cabrite's skin or fishskin?Good sword!I have one with slot at one side!

9.请教是藏蜥蜴皮是鱼皮?好刀!我有一把是单面开槽的!

10.To predict the slot film-cooing adiabatic effectiveness, a mathematic model was developed based on cohence non-isothermal jet theory.

10.摘要在伴随非等温射流基础上发展了一种适于缝槽气膜冷却绝热温比预估的数学模型。

11.Needle slot on the neilsbed armor plate is usually milled one by one by milling machine controlled manually.

11.针床钢板上的针槽通常是由人铣床一条条铣出来的，费费时，铣槽精度低。

12.This paper mainly discusses subjects such asprocessing,technology of pole coil wind ing,forming,manufacturing lead,punching,dove-tail groove,insulating,heat pr essing,encircling slot,etc.

12.本文主要研究了磁极线圈绕线、整型、引线做、鸽尾槽冲、绝缘、热压、围带槽加艺等方面内容。

13.The toolholder is used for outer slotting and the tool bar for inner slotting and for slotting the keyway.

13.机床附有电磁自动抬刀的刀架和刀杆。刀架天外插削，刀杆于内插削和插键槽。

14.Stepped and staggered sidecutter is the special miller for machining root rotor slot by Beijing Beizhong Steam Turbine Generator Co.

14.台阶错齿三面刃铣刀是北京北重汽轮有限责任公司加叶根转子槽的专铣刀。

15.The main component of knitting slot machine is "neilsbed" and there are lots of minute needle slots used to place needles.

15.针织槽机的主要部件为“针床”，长方形针床钢板（针板）槽间开有许多细密的“针槽”，于安装放置“织针”。

16.Die centering in press is obtained by milling a slot on the bottom subplate parallel to the direction of the feed.

16.通过在与进料方向平行的底部底板上铣出一个狭槽来实现压床上模具中心的调整。

17.Compared with the conventional presplitting methods, the shaped charge is obviously more effective in presplitting blasting and especially useful in controlling the presplitting slots.

17.聚能预裂爆破与普通预裂爆破相比,爆破效果明显提高,能有效地预裂缝的扩展。

18.Fitting is used for autobicycle start electrical machiney, Car forced convection air heater, Electric tool electrical machiney waits for miniature electrical machiney rotor slot insert empire paper.

18.适于摩托车起动电机、汽车暖风机、电动具电机等微型电机转子槽插入绝缘纸。

19.Each frame to doors fitted with a mortice lock is to be slotted for bolt, correctly positioned and to have a mortice cap welded on at back of perforation.

19.为匹配安装暗锁的门，每个框要为锁舌开槽，通过在其后打孔，在槽内焊接榫帽，使其正确就位。

20.Methods dip 2% lidocaine or impede narcosis, use the acuity exonerative plane root slot cut endodontium,after drying overlay thin hydrochloride zinc and than using the zinc phosphate to mount.

20.方法2%利多卡因浸润或阻滞麻醉,锐利挖器平根管口切断牙髓,拭干后氢氧化钙糊剂覆盖根髓断面,硬固后,覆薄层氧化锌粘固粉,磷酸锌粘固粉封洞。