The constraint condition for the strain energy density function of incompressible hyperelasticity is proposed.

通过对各种有限元方法的分析比较，适当修有的应变能密度函数的形式使之更适合数值计算。

The parameters of digifax is adjust by the reference of wind tunnel test result.

针对风洞实验的结果对数值模拟的各项参数设置进行调整。

Arff. which contains terms and numerical data sets for test mining weka.

这是一个基于weka数据挖掘的实验测试数据集,格式为.arff,里面包含有名词性和数值型的数据集,用于weka挖掘测试.-This is a weka data mining based on the experimental data sets format.

The IMPOWER(string) returns a complex number raised to a power.

IMPOWER(字符串;数值) 函数返回复数的幂。

"Half this number is less than 6 times the tens dight of the number by 4."

这个数值的一半比它的十位数值的6小于4.

The Six Sigma Black Belt should be able to read values from a cumulative frequency ogive.

6西格玛黑带应能从累计频次尖顶部读出数值。

A new method for predicting the motion of the hybrid monohull in regular wave is presented.

给出一种考虑粘性影响的单体复合船型运动预报的数值方法。

If nonnumeric data is input, that read and any subsequent use of the stream will fail.

如果输入非数值型数据，这次的读入以及流的后续使用都将失败。

The gust-cascade interaction noise was numerically simulated using computational aeroacoustics by solving the two-dimensional linearized Euler equations.

采用计算气动声学方法求二维线化欧拉方程对阵风与叶栅的干涉噪声进行数值模拟。

The transient process that the axialflow in the centrifuge is established under a steady thermal driving isrevealed.

通过数值求存在温度驱动情况下，离心机内形成小扰动流场的过程。

The fracturing process induced by different excavation sequence under final highwall with auger mining was numerically simulated.

对界边坡下采用螺旋钻机开采煤柱不同开采顺序引起的破坏过程进行数值模拟。

57. The Six Sigma Black Belt should be able to read values from a cumulative frequency ogive.

六西格玛黑带应该能够从累计频次分布中读出数值。

The two-dimensional axisymmetric subsonic-transonic-supersonic flow in an experimental arcjet thruster is simulated numerically using flux vector splitting method.

摘要对一实验电弧加热式发动机二维轴对称亚跨超音速流动进行数值模拟，所采用的方法是矢通量分裂算法。

The cross-section curvature ductility ratio for R.C inequiaxial T-shaped, L-shaped and cress-shaped columns is calculated by numerical method.

摘要采用非线性全过程数值分析方法，计算钢筋混凝土不等肢T形、L形和十字形柱截面模型在多种工况下的截面曲率延性比。

It is calculated as half of the value of the sampling rate.Passing this level causes aliasing distortion, or foldover.

它的计算方法是将采样率除以二，超过这个数值将会导致折叠失真，或称折叠。

The Distinct Element Method(DEM)is a discontinuum-based numerical method especially applicable to solve the discontinuity problems in jointed rock mass.

离散元法是基于不连续性假设的数值方法,它特别适合于求节理岩体中的非连续性问题。

The method simplifies the procedure of the trial function choice, and could be used in numerical calculation in geotechnique engineering.

该方法简化试函数的选择，适用于岩土工程中的各种数值计算。

Numerical simulations of laminar flow separation and reattachment occurred in an annular backstep passage are performed by the SIMPLER algorithm.

用SIMPLER算法对流过环形后台阶通道内的层流分离和再附着进行数值模拟。

In the paper, study on displacement law of blank hole for forming cylindraceous with bottom border by numerical simulation technology.

通过数值仿真研究带底孔的圆筒形件成形后底孔的变形规律,在此基础上建立带底孔的圆筒形件成形后毛料中心孔变形规律的经验公式。

Typically, plume contamination be classified into impact stains, heating contamination, deposition, chemical pollution and optical empoison according to the damage nature.

而冲击污染、化学污染和光化学污染是基于实验数据和经验公 式进行数值模拟的。